Flatness Tolerances

Tech. Info

Flatness Tolerances

Flatness is the deviation of the surface of a sheet from a perfectly flat surface.Flatness is measured by placing a sheet on a horizontal flat surface and measuring the distance to the highest point of the sheet from the flat surface, then subtracting the material thickness. 

For material 10’ in length or less the flatness variation should not exceed the amount shown in the tables.  For material over 10’ in length, the variation in flatness should not exceed the table values in any given 10’ section.  For parts under 36” in both width and length, flatness should not exceed ¼”.  For parts whose length is between 36” and 72”, the flatness variation should not exceed 75% of the flatness of a 10’ sheet for that given width.

Flatness tolerances listed below are for roller leveled sheets or plates with minimum or no margins.  When margins are required please contact us with your requirements.

Three levels of quality are available:

Commercial Quality -- Superior Quality -- Special Quality

REQUIREMENT NOTES
If your requirement is within one of the following categories, it is recommended that you discuss the flatness requirements of your perforated metal with Hendrick Manufacturing Company (1-800-225-7373)
Category Description
1 Perforated sheets with other than "safe" or "no" margins .
2 Stresses imposed during the perforating process may cause a deviation in the flatness of the edges. The wavy edge may occur in perforated sheets and coils with wide or unequal wide unperforated blank edges on the long side or when making special perforations, such as countersunk or ringed perforations , especially when using soft materials such as aluminum or copper.
3 Blank areas required within perforated area .
4 Perforated sheets with very large percentage of open area .
5 When the hole diameter and/or bar between the hole is less than the material thickness.
6 Special alloys.

FLATNESS TABLE
To 36" Width
Over 36"- 48" Width
Over 48"- 60" Width
Over 60"- 72" Width
Over 72"- 84" Width
Over 84"-120" Width
Over 120" Wide
To 36" Width
H.R. & C.R. Steel Sheet, Plate & Hot Dipped Galvanized Sheets
Thickness Range Tolerance
Commercial Quality Superior Quality Special Quality
28-20GA 3/8" 5/16"  
19-16GA 1/2" 7/16"  
15-12GA 5/8" 1/2"  
11GA-1/4" 5/8" 1/2"  
5/16"-3/8" 9/16" 15/32"  
7/16"-1/2" 1/2" 7/16"  
9/16"-3/4" 7/16" 11/32"  
Heat Treated Steel Plate (Hardness Range 185-360 Brinell)
To 1/4" 1-5/16" 1-5/32"  
1/4"-3/8" 1-1/4" 1-1/8"  
7/16"-1/2" 1-1/4" 1-1/8"  
9/16"-3/4" 1-1/8" 1"  
Stainless Steel and Other Heat Resistant Alloys Sheet & Plate
30-20GA 1/2" 7/16"  
19-16GA 5/8" 1/2"  
15-12GA 3/4" 5/8"  
11GA-1/4" 3/4" 5/8"  
5/16"-3/8" 11/16" 9/16"  
Aluminum & Copper
.012"-.032" 5/16" 1/4"  
.033"-.063" 7/16" 11/32"  
.064"-.125" 9/16" 15/32"  
.126"-.500" 5/8" 9/16"  
.501"-.750" 11/16" 5/8"  
Over 36"- 48" Width
H.R. & C.R. Steel Sheet, Plate & Hot Dipped Galvanized Sheets
Thickness Range Tolerance
Commercial Quality Superior Quality Special Quality
28-20GA 1/2" 7/16"  
19-16GA 5/8" 1/2"  
15-12GA 3/4" 5/8"  
11GA-1/4" 7/8" 23/32"  
5/16"-3/8" 3/4" 5/8"  
7/16"-1/2" 5/8" 1/2"  
9/16"-3/4" 9/16" 15/32"  
Heat Treated Steel Plate (Hardness Range 185-360 Brinell)
To 1/4" 1-5/8" 1-7/16"  
1/4"-3/8" 1-7/16" 1-1/4"  
7/16"-1/2" 1-3/8" 1-7/32"  
9/16"-3/4" 1-1/4" 1-1/8"  
Stainless Steel and Other Heat Resistant Alloys Sheet & Plate
30-20GA 5/8" 1/2"  
19-16GA 3/4" 5/8"  
15-12GA 7/8" 23/32"  
11GA-1/4" 1" 13/16"  
5/16"-3/8" 13/16" 21/32"  
Aluminum & Copper
.012"-.032" 7/16" 11/32"  
.033"-.063" 9/16" 15/32"  
.064"-.125" 11/16" 9/16"  
.126"-.500" 3/4" 11/16"  
.501"-.750 13/16" 3/4"  
Over 48"- 60" Width
H.R. & C.R. Steel Sheet, Plate & Hot Dipped Galvanized Sheets
Thickness Range Tolerance
Commercial Quality Superior Quality Special Quality
28-20GA 5/8" 1/2"  
19-16GA 3/4" 5/8"  
15-12GA 1" 13/16"  
11GA-1/4" 1-1/16" 27/32"  
5/16"-3/8" 7/8" 23/32"  
7/16"-1/2" 11/16" 9/16"  
9/16"-3/4" 5/8" 1/2"  
Heat Treated Steel Plate (Hardness Range 185-360 Brinell)
To 1/4" 1-7/8" 1-5/8"  
1/4"-3/8" 1-5/8" 1-7/16"  
7/16"-1/2" 1-7/16" 1-1/4"  
9/16"-3/4" 1-5/16" 1-5/32"  
Stainless Steel and Other Heat Resistant Alloys Sheet & Plate
30-20GA 3/4" 5/8"  
19-16GA 1" 13/16"  
15-12GA 1-1/8" 15/16"  
11GA-1/4" 1-3/16" 31/32"  
5/16"-3/8" 7/8" 23/32"  
Aluminum & Copper
.012"-.032" 9/16" 15/32"  
.033"-.063" 11/16" 9/16"  
.064"-.125" 15/16" 3/4"  
.126"-.500" 13/16" 3/4"  
.501"-.750" 3/4" 11/16"  
Over 60"- 72" Width
H.R. & C.R. Steel Sheet, Plate & Hot Dipped Galvanized Sheets
Thickness Range Tolerance
Commercial Quality Superior Quality Special Quality
28-20GA 3/4" 5/8"  
19-16GA 1" 13/16"  
15-12GA 1-1/4" 1"  
11GA-1/4" 1-3/8" 1-1/8"  
5/16"-3/8" 1-1/16" 27/32"  
7/16"-1/2" 3/4" 5/8"  
9/16"-3/4" 11/16" 9/16"  
Heat Treated Steel Plate (Hardness Range 185-360 Brinell)
To 1/4" 2-3/8" 2"  
1/4"-3/8" 1-7/8" 1-5/8"  
7/16"-1/2" 1-7/16" 1-1/4"  
9/16"-3/4" 1-3/8" 1-7/32"  
Stainless Steel and Other Heat Resistant Alloys Sheet & Plate
30-20GA 1" 13/16"  
19-16GA 1-1/4" 1"  
15-12GA 1-1/2" 1-1/4"  
11GA-1/4" 1-1/2" 1-1/4"  
5/16"-3/8" 1" 13/16"  
Aluminum & Copper
.012"-.032" 11/16" 9/16"  
.033"-.063" 7/8" 23/32"  
.064"-.125" 1-1/8" 15/16"  
.126"-.500" 7/8" 13/16"  
.501"-.750" 15/16" 7/8"  
Over 72"- 84" Width
H.R. & C.R. Steel Sheet, Plate & Hot Dipped Galvanized Sheets
Thickness Range Tolerance
Commercial Quality Superior Quality Special Quality
28-20GA      
19-16GA      
15-12GA      
11GA-1/4" 1-1/2" 1-1/4"  
5/16"-3/8" 1-1/4" 1"  
7/16"-1/2" 7/8" 23/32"  
9/16"-3/4" 3/4" 5/8"  
Heat Treated Steel Plate (Hardness Range 185-360 Brinell)
To 1/4" 2-1/2" 2-1/8"  
1/4"-3/8" 2-1/4" 1-15/16"  
7/16"-1/2" 1-5/8" 1-7/16"  
9/16"-3/4" 1-1/2" 1-5/16"  
Stainless Steel and Other Heat Resistant Alloys Sheet & Plate
30-20GA      
19-16GA      
15-12GA      
11GA-1/4" 1-3/4" 1-7/16"  
5/16"-3/8" 1-3/8" 1-1/8"  
Aluminum & Copper
.012"-.032"      
.033"-.063"      
.064"-.125"      
.126"-.500" 1" 7/8"  
.501"-.750" 1-1/16" 1"  
Over 84"-120" Width
H.R. & C.R. Steel Sheet, Plate & Hot Dipped Galvanized Sheets
Thickness Range Tolerance
Commercial Quality Superior Quality Special Quality
28-20GA      
19-16GA      
15-12GA      
11GA-1/4" 1-5/8" 1-3/8"  
5/16"-3/8" 1-1/2" 1-1/4"  
7/16"-1/2" 1-1/8" 7/8"  
9/16"-3/4" 1" 3/4"  
Heat Treated Steel Plate (Hardness Range 185-360 Brinell)
To 1/4" 2-5/8" 2-3/8"  
1/4"-3/8" 2-1/2" 1-1/4"  
7/16"-1/2" 2-1/8" 1-7/8"  
9/16"-3/4" 2" 1-3/4"  
Stainless Steel and Other Heat Resistant Alloys Sheet & Plate
30-20GA      
19-16GA      
15-12GA      
11GA-1/4" 2" 1-3/4"  
5/16"-3/8" 1-5/8" 1-3/8"  
Aluminum & Copper
.012"-.032"      
.033"-.063"      
.064"-.125"      
.126"-.500" 1-1/8" 1"  
.501"-.750" 1-1/4" 1-1/2"  
Over 120" Wide
H.R. & C.R. Steel Sheet, Plate & Hot Dipped Galvanized Sheets
Thickness Range Tolerance
Commercial Quality Superior Quality Special Quality
28-20GA      
19-16GA      
15-12GA      
11GA-1/4" 2-1/8" 1-7/8"  
5/16"-3/8" 2" 1-5/8"  
7/16"-1/2" 1-7/8" 1-1/4"  
9/16"-3/4" 1-1/2" 1-1/8"  
Heat Treated Steel Plate (Hardness Range 185-360 Brinell)
To 1/4" 3-1/8" 2-7/8"  
1/4"-3/8" 3" 2-5/8"  
7/16"-1/2" 2-7/8" 2-1/4"  
9/16"-3/4" 2-1/2" 2-1/8"