Length & Width Tolerances |
|
 |
 CARBON STEEL - Not Resquared
STAINLESS STEEL - Not Resquared
ALUMINUM - Not Resquared
Standard overall length and width tolerances |
|
|
|
| |
|
CARBON STEEL - Not Resquared |
|
|
COMMERCIAL QUALITY
Hot rolled mill edge sheets produced from coils and cut lengths including pickled. |
Sheet
Thickness |
Inches
Width |
Width
Tolerances |
Inches
Length |
Length
Tolerances |
30GA-7GA |
12-14 |
-0 +9/16" |
Up to 60" |
-0 +1" |
15-17 |
-0 +5/8" |
Over 60" - 120" |
-0 +1 1/2" |
18-19 |
-0 +11/16" |
Over 120"
|
-0 +2"
|
20-21 |
-0 +3/4" |
|
|
22-24 |
-0 +13/16" |
25-26 |
-0 +1 1/16" |
27-30 |
-0 + 1 3/16" |
31-50 |
-0 +1 3/8" |
51-78 |
-0 +1 3/4" |
SUPERIOR QUALITY
Hot rolled (mill cut edge), cold rolled and hot dipped galvanized sheets, coils and mill cut lengths including pickled sheets. |
Sheet
Thickness |
Inches
Width |
Width
Tolerances |
Inches
Length |
Length
Tolerances |
| |
To 30" |
-0 + 1/4" |
To 60" |
-0 +1" |
Over 30" - 48" |
-0 + 5/16" |
Over 60" - 120" |
-0 +1 1/2" |
Over 48" - 60" |
-0 +3/8" |
Over 120" |
-0 +2" |
COMMERCIAL QUALITY
Mill Edges and Mill Sheared Plates. |
Specified Length or
Width in Inches
|
Thickness Range |
3/16" to 3/8" |
Over 3/8" to 5/8" |
Over 5/8" to 1" |
Length or Width
Tolerance
|
Length or Width
Tolerance |
Length or Width
Tolerance
|
To 24" |
-0 +7/16" |
-0 +1/2" |
-0 +9/16" |
Over 24" - 36" |
-0 +5/8" |
-0 +11/16" |
-0 +3/4" |
Over 36" - 48" |
-0 +3/4" |
-0 +13/16" |
-0 +7/8" |
Over 48" - 60" |
-0 +7/8" |
-0 +15/16" |
-0 +1" |
Over 60" - 84" |
-0 +1 1/8" |
-0 +1 3/16" |
-0 +1 1/4" |
Over 84" - 120" |
-0 +1 1/4" |
-0 +1 5/16" |
-0 +1 3/8" |
Over 120" |
-0 + 1 1/2" |
-0 +1 9/16 |
-0 +1 5/8" |
|
|
|
| |
|
STAINLESS STEEL - Not Resquared |
|
|
COMMERCIAL QUALITY
Hot rolled and cold rolled sheets and cold rolled sheets produced from coils. |
Width Tolerance |
Thickness |
Up to 60" Wide |
30GA-16GA |
+3/8" -0"
|
Over 16GA-7GA |
+1/2" -0" |
Length Tolerance |
Thickness |
Length |
Tolerance |
30GA-7GA |
0" - 120" |
+2" |
Over 120" |
+2 1/4" |
COMMERCIAL QUALITY
Sheared Mill and Universal Mill Plates.
|
| |
Thickness
|
3/16" - 3/8" |
Over 3/8" - 1/2" |
Over 1/2" - 1" |
Width |
Length |
Width Tolerances
|
0" - 60" |
-- |
-1/4" +1/2" |
-1/4" +5/8" |
-1/4" +3/4" |
Over 60" - 84" |
-- |
-1/4" +11/16" |
-1/4" +13/16 |
-1/4" +15/16" |
| |
Length Tolerances
|
-- |
0" - 144" |
-1/4" +2 1/4" |
-1/4" + 2 1/4" |
-1/4" +2 1/4" |
|
|
|
| |
| ALUMINUM - Not Resquared |
|
|
|
COMMERCIAL QUALITY
Length and width tolerances for aluminum flat sheets and sheets from coil. |
Width Tolerance
|
Thickness |
Up to 60" Wide |
.006" to .060" |
+3/8" -1/8" |
Over .060" to .1875" |
+1/2" -1/8" |
Length Tolerance |
Thickness |
Length |
Tolerance |
.006" to .1875"
|
0" - 120" |
+2" |
Over 120" |
+2 1/4" |
COMMERCIAL QUALITY
Plate |
| |
Thickness |
.1876" - .375" |
.376" - .500"
|
.501" - 1" |
Width |
Length |
Width Tolerances |
0" - 60" |
-- |
-1/4" +1/2" |
-1/4" +5/8" |
-1/4" +3/4" |
Over 60" - 72 " |
-- |
-1/4" +11/16" |
-1/4" +13/16 |
-1/4" +15/16" |
| |
Length Tolerances |
-- |
0" - 144" |
-1/4" +2 1/4" |
-1/4" + 2 1/4" |
-1/4" +2 1/4" |
|
|
|
|
|
| |
| Standard overall length and width tolerance of resheared sheets and plates, of all metals, and plastics sheared after perforating. |
|
|
|
Tolerances |
Thickness |
Commercial
Quality |
Superior
Quality |
Special
Quality |
30GA - 10GA |
± 1/8" |
± 1/16" |
* |
8GA - 1/4" |
± 1/4" |
± 1/8" |
5/16" - 1/2" |
± 5/16" |
± 5/32 |
9/16" - 3/4" |
± 3/8" |
± 3/16" |
11/16" - 1" |
± 1/2" |
± 1/4" |
*If other special resheared tolerances are required, contact
Hendrick MFG Company.
When steel plates or aluminum sheets and plates are purchased from the mill or service center as a sheared product, the above tolerances may not be achievable. |
|
|
|
|
